Heat Embossing

Basic Pattern Decorative Masks: Trees

July 17, 2020

Decorative Masks Part IV

Card made with tree decorative pattern mask

Basic Pattern Decorative Masks (item #150697) come in a set of 4 masks, sized 6 x 6″ each. They are thin and pliable, plastic in nature and easily cleaned. The enclosed insert lists 5 different methods you can use when you create with these decorative masks: spritz, sponge, trace, emboss and texture.

In Part I of my series, I covered the Dots Mask and Embossing Paste. For Part II, I moved on to the Victorian Mask and Spritzing. Part III of this series on Decorative Masks covers the Mosaic Mask and Sponging. And in the final post of my series, I am using the Tree Mask and Heat Embossing.

Heat embossing requires the use of a Heat Tool (item #129053) and embossing powder. The result of heat embossing is shiny (or glossy) raised images that are lovely both visually and as texture.

When I heat emboss, I prefer to use VersaMark Ink, a clear ink also used to create watermark images. VersaMark Ink holds the embossing powder that needs to be heated to a melting point quite well, but a very wet ink pad in any color will also work.

Heat Tool and Embossing Powders — Stampin’ Up! Embossing Powders come in Gold, Silver, White and Clear. Over the years there have been many color versions, and I have a vast array of them. I keep the commonly used Embossing Powders in plastic containers, along with a plastic spoon for use.

I have the older Stampin’ Up! Heat Tool as well as the current version, and a wooden stand that holds either. My stand makes it hands free easy: I just turn on the heat and hold my paper under it until the powder is completely melted. I recommend using a clothespin or clip on your paper to help extend your hand away from the heat, it can get intense!

Tips For Heat Embossing

*Make sure you use the Embossing Buddy if you have one. This helps keep static off your paper and the Embossing Powder from collecting where you don’t want it. Stampin’ Up! no longer sells them, but you can purchase them elsewhere.

*Keep that VersaMark Inkpad full of ink! If the ink pad is too dry, the powder will not stick to your paper and you will have splotchy embossing. I always recommend you buy a refill when you buy an ink pad.

*If your Embossing Powder becomes damp or collects any moisture, it will not stick and melt properly. You can place a few pieces of dry rice into your container to absorb the unwanted moisture.

*You don’t have to use VersaMark! If your ink pad is really wet, you can use any color of ink with the Clear Embossing Powder and you will get wow results!

*Don’t over-heat your embossed piece. You will be able to see the melting process as the waves of heat hit your image and the powder begins to melt. Move your paper slowly under the heat so your paper doesn’t scorch and you reach all intended areas.

*Carefully inspect your embossed piece to see if you missed any areas before touching it. If you have missed an area that still has dry powder, touching it will remove the powder and leave a smudgy blank spot. Put the paper back under the heat where needed for a brief touch up.

Setting Up For Heat Embossing Success

You can heat emboss with or without a mask. Just like in my previous Decorative Mask posts, I suggest securing your paper and mask to avoid shifting mid-work.

I took advantage of a Tombow Removable Adhesive Tape Runner, and secured my cardstock to my graph paper. This kind of tape runner allows temporary holds, and is easily removed without tearing or residue. In fact, when I rub my finger across the removable adhesive, it crumbles away like pencil erasing. Only a very small amount is needed here.

Next, I secured the Basic Pattern Decorative Tree Mask in the exact position I wanted it to be. This time I used Painters Tape to hold the mask down. I made sure I did not cover my cardstock with the tape.

Preparing the Tree Decorative Mask for heat embossing use

To get a good coating of the VersaMark Ink over my mask, I removed the cover and applied the entire ink pad over the mask surface, in the same manner I would apply ink to a large stamp.

After I applied the VersaMark, I carefully removed the mask and immediately added Gold Embossing Powder to my cardstock. The plastic spoon in my container helps me scoop the dry powder over the paper. I angle the paper over the container so the loose powder goes back in without creating a huge mess.

Next up: heat embossing!

Gold embossed image using tree decorative mask — This was my first attempt at this technique. In hindsight, my VersaMark Ink Pad could have been wetter for a better application resulting in more gold powder to heat. Wherever the light is hitting the paper is where you really see the shine effect.

The VersaMark Ink left my stencil very sticky. When I rinsed it in water to clean the stencil, the residue did not go away. I added some soap and my stencil was in good shape after that!

Oh Christmas Card-inal

The beautiful gold embossing needed a fancy card layout, and the Tree Mask background brought to mind birds. The oversized cardinal stamp from the Toile Christmas Stamp Set (item #150469), and coordinating Christmas Cardinal Dies( item #150640) were the perfect fit for something special!

I began by stamping my cardinal in Memento Black Ink onto Whisper White Cardstock. I used Stampin’ Blends in a variety of colors to create my feathered friend’s look. After I die cut the cardinal out, I fussy cut some of the additional white outline and finished coloring all the edges.

Using Stampin' Blends to color cardinal from Toile Christmas Stamp Set

I stamped the branch with berries from the Toile Christmas Stamp Set in the same manner, except this time I stamped off first for a lighter black outline. Again, the Stampin’ Blends helped me create beautiful rich color in no time.

Branch stamp from Toile Christmas Stamp Set and Stampin' Blends

Merry And Bright

The sentiment I chose from the Toile Christmas Stamp Set has a coordinating die too. Because my card base and layer colors were more nature themed, I wanted my sentiment to blend in as well. I experimented with Crumb Cake and Soft Suede Cardstock using Mossy Meadow Ink.

Sentiment from Toile Christmas Stamp Set and die — The Soft Suede was more gold toned, but too dark, so I chose the lighter Crumb Cake version.

Little Embellishments

I love to add a little flair, or spray of paper fun, around my focal piece. The dies in the Christmas Cardinal Dies make this simple to accomplish. First, I die cut the green leaves using Mossy Meadow Cardstock. Next, I added a little ink by sponging the same color over them to deepen my images.

Die cut leaves from Christmas Cardinal Dies and Mossy Meadow Ink and sponge

What goes with gold? More gold. I used small scraps from my Gold Foil Sheets (item #132622) to die cut the sweetest swirls. I also pulled some Real Red Double Stitched Satin Ribbon (item #151155) for accent.

Swirl dies from Christmas Cardinal Dies and Gold Foil Paper

Flight To Success

Once I had all the elements of my card in order, the assembly process was a breeze. I used a combination of Tombow Liquid Glue, Stampin’ Seal, Tear & Tape, and Stampin’ Dimensionals for adhesive.

Finished card using heat embossing and the tree decorative pattern mask

As you can see, heat embossing with the Basic Pattern Decorative Masks is easy and versatile, and another great way to incorporate masks into your projects. If you missed any of the installments of decorative mask use, be sure to read back thru my posts for additional ideas and information.

Cards made with Basic Pattern Decorative Masks — Four different pattern masks, four different techniques, four different cards!

Looking for any of the supplies I used in my card today? Head over to my online store, https://juliemakson.stampinup.net. You will be sure to find just what you are looking for, and even more!

Ornate Garden Suite Part II

April 3, 2020

Ornate Thanks Bundle

My deep dive into the early release Ornate Garden Suite continues as Part II, with the Ornate Thanks Bundle review. My previous blog post, Ornate Garden Suite Part I, covered the various embellishments and Ornate Floral 3D Embossing Folder. Today, I am adding samples with even more stamps from the Ornate Thanks stamp set, in addition to the Ornate Border Dies.

Ornate Border Dies

The dies total 9 in this configuration. They are definitely ornate, as well as floral, so they fit the garden suite theme perfectly.

Two of the dies will cut a floral border, leaving a delicate open pattern to the right and remaining attached to the cardstock to the left. They work well on card fronts to create a peek-thru-to-the-inside effect.

Two of the dies create a lace overlay along the edge of your paper. I used them together on a single piece of cardstock with fabulous results. (See my sentiment example in the So Grateful card below.)

One of the dies cuts a floral border completely out, leaving it free standing. Another die helps to remove one of the floral borders so that it, too, is completely cut out, or free standing.

Also, there are 3 flower dies ranging from small to large in size. These die cut flowers work great in the free-standing floral border. (See my example in the Thank You card below.)

So Grateful Card

Card using products from the Ornate Thanks Bundle

My So Grateful Card is made with Blushing Bride and Whisper White cardstock. I have continued the use of the Ornate Floral 3D Embossing Folder, as can be seen here in Whisper White.

Following are some of my crafty tips:

Flower Border Die

Some of the Ornate Border Dies have tabs at each end to help you line the dies up correctly on your cardstock. If you are die cutting your card base, make sure you orient your die so that it is:

A.) cutting away to the right and leaving the left uncut.

B.) placing top of die to top of card base (in this case, the flowers are top, leaves are bottom).

I also recommend securing your dies with either a post-it note or washi tape to secure it while it travels thru your die cutting machine. There is nothing worse than the die shifting and having to start over.

The Ornate Border Dies are intricate, and require multiple cranks thru the die cutting machine. I also found the use of a shim (in the form of a thin piece of paper) useful. And between multi cranks, I rotated my sandwich base completely around (without taking the sandwich apart).

Regardless, there may be some fine picking at hand for little hangers-on. Be prepared with your die brush and/or piercing tool. And keep those extra leaves that pop out, they are perfect accent pieces!

Sentiment At Hand

For my sentiment on this card, I chose to use both edging borders, one top and one bottom. The dies are long, so my paper matches in length. Even though I don’t need all of it for this card, I can use the remainder elsewhere after trimming to size.

I chose the sentiment, So Grateful, from the Ornate Thanks stamp set. Because my card is entirely pink and white, I felt that black would be overwhelming as an ink choice. Instead, I used Early Espresso, as the rich brown melds nicely with pink but remains bold, to be well seen.

Finishing Touches

Remember those little accent leaves from the die cut above? Here they are, put to good use. After dry fitting the leaves and my sentiment, I remove the sentiment and secure the leaves with Tear and Tape Adhesive. As a final step, the sentiment covers the tape.

Thank You Card

My Thank You card features the Ornate Garden Specialty Designer Series Paper. Complementary colors Early Espresso, Old Olive and Mint Macaron were put into play. I also added So Saffron, Crushed Curry, Very Vanilla and for bright pop of fun, a Poppy Parade cardbase.

This is how it came together…

Free Standing Floral Border Die

I chose to die cut the free standing floral border die in Old Olive. Because the length is closer to 6″, and my card base is 5 1/2″, I needed to trim a bit by hand. This was easily done using my paper snips.

Difficulty Level without cat ‘helping’: 2 out of 5

Difficulty Level with cat ‘helping’: 4 out of 5

Winnie the Naughty Cat — Winnie thinks she is helpful in the craft room, but she really isn’t.

Single Flower Dies

I die cut flowers in 3 colors, Poppy Parade (which looked too Christmasy next to the Old Olive, saved for another day), Very Vanilla and Crushed Curry. The latter two made it onto my finished card, as I liked the way they layered together.

Finishing Touches

The Ornate Floral 3D Embossing Folder peeks in again in the So Saffron Cardstock. The Thank You sentiment comes from the Ornate Thanks stamp set, inked in Early Espresso. Beneath the sentiment flows Old Olive ribbon from the Ornate Garden Ribbon Combo Pack. Lastly, I added Gilded Gems to the flower centers.

So Loved Card

My third and final card today using the Ornate Thanks Bundle is elegance enhanced, showcasing Mint Macaron, Whisper White and Gold.

Here are some details in the making of this beautiful masterpiece:

Double Duty Dies

I used the rose floral border die on this card twice. The first time on the front of the card base, and the second as an additional layer to the card. With my VersaMark Ink Pad, I swiped ink on the outer die cuts of both layers and heat embossed with Gold Embossing Powder.

The front of the card peeks thru to the Whisper White Cardstoc positioned inside. The additional layer is placed over a gold foil design paper from the Ornate Garden Specialty pack.

Finishing Touches

The left-over leaves from the daisy floral border die were so fun to work with in my first card, I wanted to use them again. I die cut a piece of Whisper White just to create the leaves! Left-overs are always saved to be re-worked, so no waste there.

I used my VersaMarker to add VersaMark to the tips of the leaves for gold heat embossing. A good alternative, in lieu of the VersaMarker, would be to place some VersaMark refill liquid on a clear block, then use a blender pen to add VersaMark to the leaf tips. Keep that paintbrush handy to wipe embossing powder off unwanted areas before applying heat.

Ornate Thanks Stamp Set

The stamp sayings, “So Grateful” and “Thank You”, used in the cards featured here, are the large stamps in the set, Ornate Thanks. The stamp “Thanks” is another similar in size.

The remainder of the stamps in this 19 piece photopolymer set are smaller handwritten font (so fabulous!!), in various sayings that pair nicely with the thanks theme. All 3 of the cards shown in the Ornate Garden Suite Part I used the scripty stamps. I adore this font.

For this card, I only wanted “so loved” from the stamp “your kindness is so loved”. Masking part of the stamp before use can change up the way your sentiment reads. I added painters tape to the undesired portion of the stamp image, inked in VersaMark, removed the tape, and stamped. Heat embossing in gold finished the look nicely.

Giving Thanks

There is so much to be thankful for, and just as many reasons to send a card filled with homemade gratitude to someone you know! The Ornate Thanks Stamp Set gives you versatility with what to say, or stamp. The Ornate Border Dies put the fun in fun-ctionality, as you assemble and layer those cards or projects.

Be sure to stop by my online store to add the Ornate Thanks Bundle to your cart today. And for more creative ideas, check back soon as I continue with Part III in this series, with the Ornate Style Bundle. Don’t miss the incredible conclusion!

No Matter The Weather

March 27, 2020

Card made with Paper Pumpkin March 2020 kit

We’re In This Together

The March 2020 Paper Pumpkin kit has been a huge hit! We are all facing difficult times. The stormy clouds, adorable rainboots (let’s try to be fashionable in arduous situations!), and uplifting phrases like “wishing you brighter days ahead” and “I believe in you” are a much needed breath of fresh spring air to our tired souls.

Paper Pumpkin kits include supplies that are both consumable (like ribbons and embellishments, use them up!) and non consumable (stamp on my friends!). The kits are a great way to build up your stamp collection, and the stamps are intended to be used once all the consumables are gone.

In fact, today’s featured card uses just the stamps from the March 2020 Paper Pumpkin kit. Bonus: this embellishment-free card is flat and easily mailed! What is not missing is… the wow factor.

If you would like to print or pin the card recipe with dimensions and a list of additional supplies I used, click here.

My Creative Process

Following are some pictures of assembly, useful tips and insights in the making of this lovely card, and alternative suggestions in creation. Please read on for more details!

Embossing Raindrops

VersaMark Ink, Emboss Buddy and Emboss Powder

To make raindrops on the watercolor paper, I took the following steps:

Run Embossing Buddy over Watercolor Paper.
Using VersaMark Ink Pad, stamp raindrops from the March 2020 Paper Pumpkin Kit on Watercolor Paper. (I stamped 3 images, then sprinkled with embossing powder, tapped off excess powder and repeated the process. In this way, I could see where my raindrops would be, and where I might want more of them.)
Use the heat tool to heat set the embossing powder. I experimented with both Clear and Silver Embossing Powder in my creative process.

Heat Tool — I find that a regular paintbrush is a great way to remove excess dry embossing powder from my project before I apply the setting heat.

Pigment Sprinkles

Prepare to be amazed….and very messy! Pigment sprinkles create super unique backgrounds, no 2 will ever be the same. So therefore, instant art! Here are my steps:

Using protective tray (or box, paper plates etc), lay heat embossed watercolor paper down and spritz with water to wet randomly. Don’t over-saturate here, you will be adding more water.
Sparingly tap pigment sprinkles over wet paper. These tiny particles have a mind of their own, just remember less is better and more is mud. Watch the colors run, it is so cool!
Add additional spritzed water to help pigment sprinkles blend. It is helpful to have a paper towel on hand to absorb excess water/color, especially from the sides where it tends to pool up.
Need to add more pigment sprinkles? Do so now, but be careful not to over blend.
When satisfied with outcome, you can place a clean paper towel over your watercolor paper to absorb liquid and speed drying time. Baby wipes are useful for your messy hands!
Allow watercolor paper to dry completely. Placing it under something flat and heavy helps to keep the curling paper manageable.

Fussy Cutting

Rainboots

Fussy cutting, the use of scissors to trim an image in close capacity, is not typically first choice. But sometimes it is necessary, and practice makes…if not perfect, maybe close enough? Regardless, Stampin’ Up!’s sharp little Paper Snips make the job easier.

Stamp the rainboot outline from the March 2020 Paper Pumpkin Kit on a scrap of Whisper White Cardstock using Memento Tuxedo Black Ink.
Use the floral filler stamp from the same kit, and Pineapple Punch Ink, lining up with the outline image.
For an additional pop of fun bright color, I used the Dark Pumpkin Pie Stampin’ Blend and colored the boot label, boot straps and outlines.
Time to fussy cut! This one isn’t too bad, you can do it.

Grass

Here’s how I created the grass inserts for the rainboots:

Stamp the grass image from the March 2020 Paper Pumpkin Kit on a scrap of Granny Apple Green Cardstock using Granny Apple Green Ink.
Next, add Garden Green ink to the grass stamp and apply, overlapping the first image. This will give you thicker, greener grass. Who doesn’t want that?
Time to fussy cut. This one is a bit hard, once you get it sliced in half. I recommend first tackling the sides (make sure you leave a nice base at the bottom for handling), then when ready to do the grass fronds, snip downward from the top. Making little x patterns or spear shaped cuts is helpful.
After I fussy cut the grass, I applied the grass stamp with Granny Apple Green ink to each half to overlap (again) the previous grass. The illusion here is that you are really good at fussy cutting!
With the White Stampin’ Chalk Marker, I added tiny dots to the top of the grasses. This brightness adds the look of dainty flowers.

Sentiment

No Matter the Weather We Are in This Together Stamp

You are not alone in this. This card speaks comfort. To create the embossed verse, here are my steps:

Using your paper snips, flag the end of the Bermuda Bay Cardstock. I start at the bottom corner and cut straight toward the middle, stopping there. Next, I start at the upper corner and do the same, meeting in the middle to remove the triangle cut away.
Run Embossing Buddy over Bermuda Bay Cardstock to prevent embossing powder from sticking where you don’t want it.
Ink stamp saying form the March 2020 Paper Pumpkin Kit in Versamark, apply to cardstock.
Immediately sprinkle White Embossing Powder over Versamark image.
Tap off excess embossing powder and heat emboss to set.
I love sponging to add interest and depth. I added Bermuda Bay ink to the outer edges of the flagged sentiment piece using my designated sponge. (Yes, I am that person, designated sponge.)

Putting It All Together

All the hard work is done! Now it is time to assemble your card layers. As mentioned earlier, this card is flat, and easily mailed. However, if you choose to add dimension or embellishments, get creative!

Quick Tips

I used Tear and Tape Adhesive to attach the watercolored paper to the Whisper White Cardstock. This great holding tape really secures the heavy paper with its tendency to curl.
I used (Tombow) Multi-Purpose Liquid Glue to tuck the grass fronds into each boot. The wiggle room you have with this glue lets you move the grass around a bit to get the best angle.
Play with the placement of your sentiment piece. Depending on your creative outcome from the pigment sprinkles, you may need to adjust the height as you desire.
The process for heat embossing on this card is optional. If you have raindrop embellishments, use them instead. Craft Whisper White Ink can be used to stamp the sentiment instead of heat embossing it, and will look similar.

I hope you enjoyed my tips and techniques in the making of this card using the stamps from the March 2020 Paper Pumpkin kit! Be sure to sign up for my email newsletter, where I share more tutorials for free.

And if you need any of the supplies to create this card in your own stamp studio, shop my online store, https://juliemakson.stampinup.net, anytime.